Connect Optical Transceivers of Different Brands, Fibers or Wavelengths?

Optical transceivers usually work coordinately on a pair of network switches. As switch is responsible for directing the flow of data, optical transceiver works for transforming light to data or the opposite. Then how do two transceiver modules work with each other? Can I connect two optical transceivers of different brands, fiber types or wavelengths? You can find answers here.

How Do Two Optical Transceiver Talk to Each Other?

It is known to all that the fiber optic transceiver contains a transmitter and a receiver in the same component. These are arranged in parallel so that they can operate independently from each other. When working on two switches in the same network, the transmitter on one optical transceiver takes an electrical input and converts it to an optical output from a laser diode or LED. The light from the transmitter is coupled into the fiber with a connector and is transmitted through the fiber optic cable plant. The light from the end of the fiber is coupled to a receiver on the other transceiver where a detector converts the light into an electrical signal which is then conditioned properly for use by the receiving equipment.

How optical transceiver works

Fig1. How optical transceiver works

Can I Connect Two Optical Transceivers of Different Brands, Fibers or Wavelengths?

When people are under-budgeted or in urgent need of original optical transceivers that are out of stock, they may turn to other or third-party transceivers. But how to make different transceivers work coordinately without link failure? Is it possible to connect two optical transceivers of different brands, fibers or wavelengths?

Optical Transceiver of Different Brands

As is known to all, fiber optic transceivers are manufactured with a lot of standards and protocols. If the SFP types are of the same protocol at each end, for example: both sides with SX, LX or whatever is currently in use, you can build the link between them. Please note that only the identical protocol is far more enough.

If the network switch comes from different vendors and optical transceivers with different protocols, you will get a dead link between network switch and the transceiver, thus the whole network fails. Make sure the transceiver and the switch at both ends are compatible with each other. However, as the transceiver compatibility is introduced to the optic field, many optical transceivers are now produced to be compatible with other brands. FS almost has no transceiver compatibility issues with other brand switches as all the optical transceivers have been tested to ensure its compatibility before shipping.

Optical Transceiver with Different Fiber Types

Common sense says a multimode sfp cannot work well with a single mode sfp, as the single mode fiber features a narrow core, allowing only a single mode of light to propagate while the multimode fiber has a wider core enabling multiple modes of light to propagate.

Well, as the network evolves, it is unavoidable to use single mode devices on the existing multimode fiber cables, which forces the birth of the mode conditioning cable used for single mode to multimode conversion. It is generally a duplex multimode cable that has a small length of single mode fiber at the start of the transmission length. As for optical transceiver with single mode fiber, connect the single mode connector of the cable into the transmit bore of the transceiver, and multimode connectors of the cable into the receive bore of the transceiver with all other connections going as normal.

Optical transceiver works with mode conditioning cable

Fig.2 Optical transceiver works with mode conditioning cable

Optical Transceiver on Different Wavelengths

A given transceiver generally supports a specific wavelength for both transmitting and receiving. It is vital the wavelength of the fiber optic transceivers (850nm, 1310nm, 1550nm) matches on each end, as a 1310nm sfp transceiver will not talk to a 850nm sfp transceiver. Data transmission implies that data is sent from one end to the other. The SFP transceiver on one end converts electrical signals into optical signals. A built-in laser transmits light through the fiber to the other side. Here, an optical diode converts the light back into an electrical signal. To guarantee that the SFP at the other end is capable of doing this, the SFPs at both ends should support the same wavelength.

Different wavelengths of optical transceiver
Fig.3 Different wavelengths of optical transceiver

Conclusion

To make sure your optical transceivers work smoothly with each other, be careful about their protocols, wavelengths and fiber types in case of link failure. FS provides a great range of fiber optic transceivers with no transceiver compatibility problem and transceiver prices are very competitive.